Calcium-based coordination polymers from a solvothermal synthesis of HKUST-1 in 3D printed autoclaves

A mixed-metal 1D coordination polymer [CaCu(HBTC)₂(H2O)₈]_n (where H₃BTC – benzene-1,3,5-tric arboxylic acid) was obtained in a solvothermal synthesis of a well-known copper-containing metal–organic framework [Cu₃(BTC)₂(H₂O)₃]_n (HKUST-1) in autoclaves 3D-printed from commercial polypropylene. This material was a source of calcium ions, apparently, leaking from a colorant (calcium carbonate) promoted by glacial acetic acid as a modulator used to produce large single crystals of HKUST-1. This finding was confirmed by elemental analysis and a model experiment that resulted in a new calcium-based 1D coordination polymer [Ca(H₂BTC)₂(H₂O)₅]_n under the same solvothermal conditions with no copper or calcium salts put into a 3D-printed autoclave.     

Human-to-metal electrostatic discharge current measurements – Notes on the ESD current waveform

The Electrostatic Discharge (ESD) phenomenon has been described through the IEC 61000-4-2. ESD current parameters' values, have been set in this Standard. The theoretical ESD current waveform defined in this standard, describing the conventional Contact discharge mode, needs to be re-evaluated on the basis of accurate experimental data. Even though the standard deals with commercial ESD generators, its goal is to simulate the natural phenomenon as good as possible. More and accurate data may contribute to the better simulation of the natural phenomenon. New values and better comprehension of the phenomenon demand new measurements based on high end measuring equipment. Such works and publications have been carried out the past years. Yet, the need to systematize and integrate this work remains. Larger and trust-worthy series of measurements need to be carried out and presented clearly.This paper deals with new ESD-current data, taken with broadband equipment. New and more detailed measurements like these, were never before taken at such a large number of individuals. The goal of this work is that the data acquired can serve as a basis for re-evaluating the conventional approach of the scientific community to the ESD event.In this paper, using a broadband measuring system, new parameters' values are measured and relations are presented, following standard statistical procedures. The results, which occur from measurements carried out on tenths of human individuals, are questioning the Standard in many points. A new way of approaching the standardization of the ESD current is proposed, as the excuse of the poor measuring equipment that sets barriers on the measuring accuracy, does not apply any more. The charging voltages of 500 V and 1000 V were also examined since such range of voltages are often met at ESD events and they are considered very harmful.     

光束发散度对紫外写入光纤光栅的影响

用傅里叶衍射光学分析了准分子激光束发散度对于光纤光栅制备的影响，发现光束发散角使光纤光栅的布拉格波长发生改变，相位版后干涉场沿光纤轴向和径向不均匀，对制备30dB高反射率光纤光栅造成困难。实验结果与理论分析基本一致，相对于理想平行光束情况，会聚光束使得光纤光栅布拉格波长出现在短波一边，发射光束使得光纤光栅布拉格波长出现在长波一边。     

用等厚干涉测定液体折射率

介绍一种采用等厚干涉原理测定液体折射率的简单可靠的方法。     

计算全息检测非球面干涉场的理论分析与实验结果

本文应用光学全息术及傅里叶光学的理论对计算全息图干涉检测非球面面形的光路及干涉场进行了理论分析,提出了其干涉场为不定域干涉的观点,并在实验中予以证实.     

Focusing and diffraction by an optical lens and a small circular aperture

Based on the vectorial Rayleigh–Sommerfeld diffraction integrals, analytical expressions for the transversal and axial field distribution of plane waves propagating through a thin lens followed by a small circular aperture are derived and used to study the focusing and diffraction properties of plane waves. Some special cases of our general result are discussed, and illustrative numerical calculation results are given. It is found that the vectorial nonparaxial approach should be applied if the aperture dimension is comparable with the wavelength or the focusing is strong.     

Surface structures formed by individual adsorption and coadsorption of Mn and Bi on Cu(0 0 1), studied by LEED

We have studied the individual adsorption of Mn and Bi, and their coadsorption on Cu(0 0 1) by low-energy electron diffraction (LEED). For Mn, we have determined the c(2 × 2) structure formed at 300 K, whose structure had been determined by several methods. We reconfirmed by a tensor LEED analysis that it is a substitutional structure and that a previously reported large corrugation (0.30 Å) between substitutional Mn and remaining surface Cu atoms coincides perfectly with the present value. In the individual adsorption of Bi, we have found a c(4 × 2) structure, which is formed by cooling below ∼250 K a surface prepared by Bi deposition of ∼0.25 ML coverage at 300 K where streaky half-order LEED spots appear. The c(4 × 2) structure has been determined by the tensor LEED analysis at 130 K and it is a substitutional structure. In the coadsorption, we found a c(6 × 4) structure, which has been determined by the tensor LEED analysis. It is very similar to the previously determined structure of the c(6 × 4) formed by coadsorption of Mg and Bi, and embedded MnBi₄ clusters are arranged in the top Cu layer instead of MgBi₄. Large lateral displacements of Bi atoms in the c(6 × 4)-(Mn + Bi) suggest that the Mn atoms undergo the size-enhancement caused by their large magnetic moment.     

用变形全息透镜实现变形分数傅里叶变换

利用一发散点光源和一束倾斜平行光制作出在两个垂直方向上具有不同焦距的变形全息透镜,且用此全息元件实现了变形分数傅里叶变换。变形全息透镜两个方向上的焦距随全息记录条件和再现条件而变化,分析了用这种全息透镜实现变形分数傅里叶变换的条件。实验表明,用该元件能够方便地实现任意级次的变形分数傅里叶变换。     

超声光栅实验及其多普勒频移的一种简单研究方法

采用光子学方法,对超声光栅衍射实验和实验中出现的多普勒频移现象进行了研究,所得结论与采用光的波动性观点的惠更斯-菲涅耳原理及傅里叶变换等常规方法相同.该方法进一步加深了对衍射的本质和光的粒子性的理解并对光子的信息传递能力有初步的认识.